In the application process of manufacturing waste gas purification equipment, oil leakage may occur occasionally. In view of this phenomenon, people should stop the operation of the equipment immediately and check what causes the oil leakage of industrial waste gas equipment. In view of this situation, some existing problems have been found. The following Jiangmen waste gas and wastewater treatment equipment company has compiled Bring us some knowledge.
1. Unscientific planning
It includes that the planning product staff did not fully consider the sealing or did not understand the sealing process; the sealing structure method was not scientific, which was not suitable for the working attitude, load specification, temperature and material characteristics, and did not pay attention to the anti rust, sensational, pressure equalizing and smooth Countermeasures of the equipment; and did not consider the elements such as air exchange, oil pump, fluid conduction and disassembly.
Second, the fineness of manufacturing and extrusion molding is not good
In the manufacturing process, vertical extrusion molding is not vertical, coordination is not good, poor coaxiality, finish is too high, resulting in defects such as exhaust port and sand hole during forging, and other factors with poor manufacturing and extrusion quality will lead to leakage.
3. Improper selection of rubber seals
Therefore, the selection of raw materials for waste gas purification equipment in manufacturing industry is unscientific and cannot be integrated into the sealed load specification, which leads to leakage. Rubber seals usually have high density, resilience, corrosion resistance, ozone resistance, radiation resistance, abrasion resistance and other basic characteristics. According to different load specifications, people can choose the raw materials with key characteristics to fit the sealing specification.
Fourth, supervision and maintenance are not tight
It is understood that it is the root cause of equipment leakage, such as sealing components beyond the service life, but not immediately removed and replaced, loose standard parts, gland not immediately clamped and adjusted.
V. wrong installation method
Many causes of leakage are improper installation position, excessive axial force, side crack of sealing material, different torque force of tightening screw, and incorrect assembly process.
Vi. load specification point
It includes irritant, sensational, high temperature and high pressure, dust and external material corrosion.
Source: Jiangmen waste gas and wastewater treatment equipment company http://www.toquesparamulheres.com
How to maintain environmental protection equipment in Jiangmen
1. The user shall carry out the concrete foundation construction according to the basic data provided by our company; the equipment should be installed on the concrete foundation more than 100 mm above the ground; 2. The supporting pipes and valves shall be separately supported and shall not be fixed on the tower equipment; 3. Attention shall be paid to the protection of the equipment during installation, so as not to damage the machine body and exposed parts. When the tower flange is connected
Ten maintenance details of spray tower of Jiangmen Guoqi environmental protection waste gas treatment equipment
Exhaust tower, in the type of exhaust tower, is one of the exhaust towers with long service life. It can deal with almost all mixed gases, so far it is a very practical and cheap product in the treatment of mixed waste gas. It is widely used in chemical industry, light industry, printing and dyeing, medicine, pharmacy, steel, machinery manufacturing, electronics, electroplating, painting, paint and other industries. It mainly deals with tail gas such as sulfuric acid, nitric acid and hydrofurani
Common points for attention in installation of waste gas and wastewater treatment equipment in Jiangmen
1. The user shall carry out the concrete foundation construction, and the installation surface of the foundation shall be on the same horizontal plane, and the allowable error shall not be greater than 5mm. The exhaust pipe of purification tower can be fixed by derrick type, and the foot is fixed with embedded steel plate by welding or embedded bolt. Therefore, the purification tower can not be fixed in general. The matching FRP fan is generally designed as steel frame vibration damping pedestal
Analysis of waste gas treatment equipment including those five factors
Waste gas treatment equipment is also known as waste gas purification equipment. Waste gas treatment refers to the pretreatment of the waste gas produced by industrial sites and factory workshops before discharge, so as to meet the national standards for external emission of waste gas. Today we Jiangmen environmental protection equipment home for you to introduce the analysis of waste gas treatment equipment including which five factors. General waste gas treatment includes organic waste gas tre